Jadwal Sholat

Memuat jadwal sholat…

Teknik & Rekayasa editorial

Open AccessOA2022

Dual‐Interface‐Reinforced Flexible Perovskite Solar Cells for Enhanced Performance and Mechanical Reliability

A dual-interface reinforcement strategy using a self-assembled monolayer at the ETL/perovskite interface and an in situ grown low-dimensional perovskite capping layer at the perovskite/HTL interface simultaneously improves mechanical and optoelectronic properties of flexible perovskite solar cells, achieving 21.03% PCE, 1000 h T90 operational stability, and 10,000 cycles n88 mechanical reliability.
Zhenghong Dai; Shunran Li; Xing Liu; Min Chen; Christos E. Athanasiou; B. Sheldon; Huajian Gao; Peijun Guo; N. Padture· Advances in Materials· 2022· DOI 10.1002/adma.202205301

The core problem

Flexible perovskite solar cells (f-PSCs) are attractive for portable and wearable photovoltaics but suffer from mechanical fragility at critical interfaces, particularly between the electron-transport layer (ETL) and the 3D metal-halide perovskite (MHP) film, and between the 3D-MHP film and the hole-transport layer (HTL). These interfaces are vulnerable to delamination and crack formation under bending, which degrades both power-conversion efficiency (PCE) and operational stability. Prior efforts have typically addressed only one interface or focused solely on optoelectronic passivation without considering mechanical reinforcement. This work introduces a dual-interface reinforcement strategy that simultaneously strengthens both interfaces while also enhancing their optoelectronic properties, aiming to overcome the trade-off between efficiency, stability, and mechanical reliability in f-PSCs.

Innovation

The ETL/3D-MHP interface was reinforced using a self-assembled monolayer (SAM) that improves adhesion and mechanical toughness. The 3D-MHP/HTL interface was reinforced by an in situ grown low-dimensional (LD) MHP capping layer, which provides mechanical interlocking and passivation. Interfacial mechanical properties were measured and modeled to quantify the reinforcement. The resulting dual-interface-reinforced f-PSCs were fabricated and characterized for PCE, hysteresis, operational stability (T90, duration at 90% of initial PCE retained), and mechanical reliability (n88, number of bending cycles at 88% of initial PCE retained). The scientific underpinnings of the synergistic enhancements were elucidated through combined experimental and modeling analyses.
Introduction
Flexible perovskite solar cells (f-PSCs) are attractive for portable and wearable photovoltaics but suffer from mechanical fragility at critical interfaces, particularly between the electron-transport layer (ETL) and the 3D metal-halide perovskite (MHP) film, and between the 3D-MHP film and the hole-transport layer (HTL). These interfaces are vulnerable to delamination and crack formation under bending, which degrades both power-conversion efficiency (PCE) and operational stability. Prior efforts have typically addressed only one interface or focused solely on optoelectronic passivation without considering mechanical reinforcement. This work introduces a dual-interface reinforcement strategy that simultaneously strengthens both interfaces while also enhancing their optoelectronic properties, aiming to overcome the trade-off between efficiency, stability, and mechanical reliability in f-PSCs.

Why it matters

The synergistic enhancements are attributed to the dual-interface reinforcement: the SAM at the ETL/3D-MHP interface improves adhesion and reduces mechanical stress, while the in situ grown LD-MHP capping layer at the 3D-MHP/HTL interface provides mechanical toughening and defect passivation. Together, these modifications not only strengthen the interfaces against bending-induced degradation but also improve charge extraction and reduce non-radiative recombination, leading to higher PCE and stability. The work elucidates the scientific underpinnings of these improvements and establishes a general design principle for mechanically robust, high-performance flexible perovskite solar cells. The combination of 21.03% PCE, 1000 h T90, and 10,000 cycles n88 represents a significant advance toward practical flexible photovoltaics.

Who should read this

Pembaca Research Digest dan praktisi rumpun ini.

Opening member content…