Jadwal Sholat

Memuat jadwal sholatโ€ฆ

Fisika & Matematika editorial

Open AccessOA2025

Mathematical Modeling of Signals for Weight Control of Vehicles Using Seismic Sensors

This study presents a passive dynamic vehicle weighing method using seismic signals from wheels passing over road strips, processed with FFT, matched filtering, and regularization. Field tests achieved 8.7% weight error, 1.2 km/h speed error, and 96.5% axle-count accuracy with minimal infrastructure.
N. Martyushev; B. Malozyomov; Anton Y. Demin; A. Pogrebnoy; E. Efremenkov; D. V. Valuev; Aleksandr E. Boltrushevichยท Mathematicsยท 2025ยท DOI 10.3390/math13132083

The core problem

Accurate vehicle weight monitoring is essential for road safety, infrastructure protection, and intelligent transport systems (ITS). Traditional weigh-in-motion (WIM) systems often require sensors embedded in the pavement, which are costly to install and maintain. This paper proposes a passive dynamic weighing approach that leverages seismic signals generated when vehicle wheels pass over specially applied strips on the road surface. The method aims to provide a low-cost, non-intrusive alternative for weight control. The authors highlight the challenge of separating overlapping axle responses and introduce linear-frequency-modulated (LFM) signals to enhance resolution. The study builds on spectral processing techniques, including fast Fourier transform (FFT), matched filtering, and regularization for inverse problems, to extract vehicle speed, weight, and axle count from seismic data.

Innovation

The proposed method uses an array of eight geophones deployed along a road section to record seismic vibrations induced by passing vehicles. The road surface is modified with strips that generate characteristic seismic responses, particularly LFM signals, which allow individual axle contributions to be distinguished even when they overlap in time. Signal processing involves several steps:

1. **Preprocessing**: Raw seismic signals are filtered to remove noise.
2. **Spectral Analysis**: FFT is applied to transform signals into the frequency domain, where LFM characteristics are analyzed.
3. **Matched Filtering**: A matched filter is used to detect and isolate axle responses, improving signal-to-noise ratio.
4. **Inverse Problem Solution**: Regularization methods are employed to solve the inverse problem of estimating vehicle weight from the seismic amplitudes, mitigating ill-posedness.
5. **Parameter Estimation**: Vehicle speed is derived from the time delay between geophone signals, and axle count is determined from the number of detected peaks.

The mathematical model can be summarized as follows: Let be the received seismic signal, which is a convolution of the source signal (generated by the wheel-strip interaction) with the earth's impulse response , plus noise :

Using FFT, the signal is transformed to the frequency domain: . Matched filtering involves correlating with a reference LFM template to enhance detection. Weight estimation is formulated as a regularized least-squares problem:

where represents the vector of axle weights, is a sensitivity matrix derived from the model, and is a regularization parameter. The solution is

.

Introduction
Accurate vehicle weight monitoring is essential for road safety, infrastructure protection, and intelligent transport systems (ITS). Traditional weigh-in-motion (WIM) systems often require sensors embedded in the pavement, which are costly to install and maintain. This paper proposes a passive dynamic weighing approach that leverages seismic signals generated when vehicle wheels pass over specially applied strips on the road surface. The method aims to provide a low-cost, non-intrusive alternative for weight control. The authors highlight the challenge of separating overlapping axle responses and introduce linear-frequency-modulated (LFM) signals to enhance resolution. The study builds on spectral processing techniques, including fast Fourier transform (FFT), matched filtering, and regularization for inverse problems, to extract vehicle speed, weight, and axle count from seismic data.

Why it matters

The study confirms that seismic signals combined with advanced spectral processing can achieve accurate vehicle weight and speed estimation at minimal cost. The 8.7% weight error is competitive with traditional WIM systems, while the 96.5% axle count accuracy is promising for traffic monitoring applications. The use of LFM signals is a key innovation, enabling robust separation of overlapping axle responses. The regularization approach effectively addresses the ill-posed nature of the inverse problem, though the choice of regularization parameter requires careful tuning. The system's scalability makes it suitable for integration into intelligent transport systems, where it could provide continuous, non-intrusive weight monitoring. Limitations include potential sensitivity to environmental noise and the need for initial calibration. Future work may explore machine learning for improved signal classification and adaptation to varying road conditions.

Who should read this

Pembaca Research Digest dan praktisi rumpun ini.

Opening member contentโ€ฆ